how to bypass washing machine water level sensor

how to bypass washing machine water level sensor
how to bypass washing machine water level sensor

How to Get Around the Washing Machine Sensor for Water Level
Washing machines are getting more technologically advanced and energy efficient. You may need more water for filthy clothing on occasion. You must learn how to bypass the washing machine eater level switch if you do not have one. Continue reading to find out more.

Washing Machine Quick Water Level Bypass Formula
Here’s a quick method to accomplish it:

  • Assume you have 2 lbs of clothing.
  • Fill the washtub with the 2 lbs of clothes.
  • Pour 4 lbs of water over the clothing before starting the wash cycle and let the water to sink into the fabric.
  • Start the washing machine. The machine will believe the weight is 6 lbs rather than 2 lbs, and it will automatically fill water for 6 lbs fabric loads.
  • You have successfully circumvented the water level sensor.
  • This works regardless of whether the machine is High Energy Efficient or not. There will be no harm to the washing machine, and there will be no bypassing of the electrical system, which would invalidate the warranty.
how to bypass washing machine water level sensor
how to bypass washing machine water level sensor

The Water Level Switch: An Overview

When the tub has to be filled during a wash cycle, the water level switch, also known as the “pressure switch,” on your washing machine sends electricity from the timer control to the temperature switch and water intake valve. As the tub fills, the switch shuts off the water flow when the level inside matches to the load setting – big, normal, or small.

The switch then instructs the motor to begin agitating. Depending on the type and manufacturer of your machine, the water level switch may be located in a variety of locations. In most instances, the switch is located within the control console. It is readily identified by the rubber tubing that links the switch to the tub’s side.

Water flows down the tube from the base when the washing machine fills, creating pressure. When the pressure reaches a particular level, the switch will cut off the supply of water to the washing tub.

how to bypass washing machine water level sensor

washing Machine Placements
washing Machine Placements

High-efficiency washers may save up to 80% of the water they use. They also enable you to save up to 65 percent of the energy expenses associated with running the washer. However, the amount of water available for washing individual loads is not always sufficient.

Some individuals have expressed dissatisfaction with:

They had soap scum and residue on their clothes.
Items of clothes that felt dry despite having been washed
Smells like though the garments haven’t been washed
Having to put the items through a second cycle

How to Use a High-Efficiency Washing Machine
As previously stated, high efficiency washing machines struggle to provide enough water levels for clothing.

It’s particularly bad for stinky and filthy clothing. The truth is that dirty clothing just need more water!

Smaller filthy clothing may also be difficult to spin in these high-efficiency machines.

The water level provided for the smaller clothing is likely to be excessive, resulting in an unbalanced washer. The clothing may be clean, yet they may still be damp.

One simple remedy to this issue would be to fool the water level switch. If the load in the wash tub is heavier, the water level switch will raise the necessary water level.

If the load is heavier, the washer is also more balanced when spinning. This results in more efficient spinning. In conclusion, greater mass is needed.

Old thin towels may be utilized to add bulk to your wash tub. Choose outdated towels whose colors can no longer be washed out of the other garments.

Also, make certain that they are already clean. Remember that you don’t need more clothing to clean; you simply need greater bulk to accommodate higher water levels.

Making the garments in the wash tub heavier by getting them wet is another method to fool the water level switch into increasing the water level.

Pour a gallon of water over your clothing after putting them into the wash tub. The clothing will absorb water and grow heavier as a result.

Because of the heaviness of the wet clothing, the pressure switch will activate greater water levels.

Including Thin Towels in Your Load

You may also include some thin towels made of a heavier cotton fiber. This saves room for your clothes but adds weight to your washer. The water level sensor will then cause additional water to be absorbed by your clothes.

Putting Water on Your Clothes
Water can support a lot of weight. You may put a load of clothing in the washing and pour 2 to 4 cups of water over it. Allow the water to rest for 10 to 15 minutes.

The 2 to 4 cups will add 3 to 4 pounds to the total weight. This would be sufficient to cause your sensor to discharge additional water. The best aspect about this technique is that you don’t have to add any more clothes to your burden.

Leave a Comment